2PIN MALE CONTACTOR WHITE TOYOTA Air Jet Loom Part HL1208 Wiring Plug Housing
Product Overview
2-pin male connector, white housing, for Toyota air jet loom wiring. Item code HL1208, reference HL1208. Supplied with contacts, ready for crimping.
Two pins carry one circuit. That makes this the smallest connector on the loom and the one a mill buys most often, because it sits at the end of every coil lead, valve lead and sensor lead on the machine.
Applications & Compatibility
- Application: loom wiring harness, 2-pin male connection
- Our item code: HL1208
- Reference: HL1208
- Housing colour: white
- Original part number: not marked on the housing; quote by reference HL1208
Send photographs of the housing, the mating half and the wire side with the machine number. Keying, latch type and wire gauge decide fitment before the pin count does.
Two Pins, One Circuit
- Polarity carries the whole function - on a coil or valve lead, two pins reversed is a diode taken out of the circuit.
- Mark the wires before you cut - a paint pen line costs seconds and saves a solenoid.
- One circuit, one fault - a 2-pin connector rarely half-fails: it works, or the function is dead.
- Keep a handful on the rack - the cheapest part in the store is the one that ends a night shift early.
- Check the mating half - a new plug on a worn socket is half a repair, and it will be back.
Two pins look forgiving. They are not: the smaller the housing, the more of the electrical decision it carries.
The Connector Nobody Diagnoses
- Symptom - a solenoid, valve or sensor stops responding, and the part gets replaced.
- First test - wiggle the connector while the function is commanded. If the function stutters, the fault is at the plug, not at the device.
- Second test - measure at the pins, not at the device terminals, so the connector stays in the circuit.
- Third test - a crimp can look closed and still be open. Pull test the wire, and look at the wire strands, not the insulation.
- Fourth test - retention. If the latch does not click, vibration will finish the job on the next shift.
Many solenoid and valve replacements are connector replacements that arrived one step late. Testing at the plug first is cheaper than testing at the parts counter.
Quality Standard
- Correct 2-pin configuration, colour and keying checked against the reference before packing.
- Pin straightness, cavity walls, latches and locking features checked on every unit.
- Contacts matched to the housing series and pull-tested on a sample basis from each batch.
- Housing material and colour compared against the reference for consistency.
- Bagged and labelled with the reference; batch recorded.
- Warranty against manufacturing defects, assessed case by case; damage from reversed polarity, pulling on the cable, forced mating or heat exposure is not covered.

Specifications
| Product | 2-pin male connector housing |
| Poles | 2 |
| Housing Colour | White |
| Item Code | HL1208 |
| Reference | HL1208 |
| Original Part Number | Not marked - quote by reference HL1208 |
| Supplied With | Contacts, ready for crimping |
| Testing | Pin straightness, cavity walls and locking features checked; contacts pull-tested |
| HS Code | 8536699000 |
| Place of Origin | Shanghai, China |
Order & Shipping Information
- Minimum order quantity: 10 pieces.
- Sample order is acceptable for quality evaluation.
- Stock items ship within 5 working days after payment confirmation.
- Bagged in a neutral export carton with pins protected.
- Shipping option: DHL / FedEx / UPS express, air freight, sea freight.
- Complete export documents including commercial invoice and packing list will be supplied.
- We ship worldwide to textile markets across Southeast Asia, Central Asia, South America, North America and Europe.

Frequently Asked Questions
Q1: Why is a 2-pin connector worth stocking?
It terminates every coil, valve and sensor lead on the loom, it is the cheapest part in the store, and a failed one stops a shift. Keeping ten on the rack costs less than one call-out.
Q2: Does pin orientation matter?
On coil and valve leads, yes. Reversed pins can take a diode out of the circuit. Mark the wires before cutting and keep the orientation of the original plug.
Q3: The device was replaced and still no function. Why?
The plug or the crimp is the likely fault. Wiggle the connector while the function is commanded, and measure at the pins so the connector stays in the circuit.
Q4: Should I replace the mating half as well?
If the socket is worn, yes. A new plug on a worn socket is half a repair and it will return.
Q5: How is the warranty handled?
Manufacturing defects are covered case by case. Damage from reversed polarity, pulling on the cable, forced mating or heat is excluded.
Send your inquiry directly to us